#Drok battery monitor 48volt full#
#Drok battery monitor 48volt series#

If you donвЂ™t need to change other parameters, press to quit. Press to change the parameters, press to carry bits.

Left side to switch ON or OFF Right side select the delay time (10/30/60/120 unit:S) On this menu, delay OFF and the delay time can be set, as shown in P4: Note: Please set parameters according to the battery specifications, otherwise, the percentage value is inaccurate the voltage value is accurate.ДЄll parameters are subject to the last save. L7 represents 4 string lithium 4.2V*7S=29.4V.ДЇ4 represents 4 string lithium iron phosphate battery 3.2V*4S=12.8V.ДЇ8 represents 8 string lithium iron phosphate battery 3.2V*8S=25.6V. е…ѓ represents 3 string lithium 4.2V*3S=12.6V. If you donвЂ™t need to change other parameters, long press to quit. Long press to save after finishing selection.

#Drok battery monitor 48volt series#

Press to select the appropriate battery specifications, enter L/F to select the battery series quantity. P stands for lead-acid batteries, and the numbers behind represent voltage.Д®nter the menu 1вЂ“, as shown in P3, and display 1вЂ“L/P/F xx, press to switch among L, P, and F. Under this menu, you can change the default parameters speedy: L represents the lithium battery, and the latter figure is the series quantity ДЇ represents the lithium iron phosphate battery, and the latter figure is the series quantity The main menu has 5 sub-menus: 1вЂ“, 2вЂ“, 3вЂ“, 4вЂ“, 5вЂ“.ДЎ-: Select built-in preset battery specification: lithium battery, lead-acid battery, LFP battery.Дў-: Setting Delay Time Delay OFF/ON, and select Delay TimeДЈ-: The voltage of percentage 0 to 100 could be customed.Д¤-: Buzzer switch and alarm value setting.ДҐ-: Calibrate the instrument voltage again.ДҐ.Press, select the menu to enter, long press to quit.Д¦.All parameters are subject to the last save.Power-on status, press last about 5 seconds, enter the main menu, as shown in Figure P2.If the battery specification is special, you can enter the programmable mode 3вЂ“ and reset the upper and lower limits of the battery.

Low voltage buzzer alarm (Selective assembly).

The red lightning flashes the alarm when the battery is low.

When the battery is connected to the charger or the discharge of the large current load, the display parameters will fluctuate.

The percentage on the display interface is the percentage of the remaining battery power.

The voltage on the display interface is measured in real-time, and the voltage value is displayed on 10-100V.

The battery icon on the display interface, from the right to the left, are 7 display boxes representing the battery power from low to high.

Press in the working status, you can switch the voltage and temperature to display.

In close status, you can wake up the instrument by pressing any button.

After the instrument is powered on, it shows the percentage of the battery power, the voltage, and the battery icon.

Redline to the positive terminal, black line to the negative terminal.

External NTC temperature sensor, please put the sensor to measure the temperature of the parts, do not squeeze the sensor (selective assembly).

PH2.0 terminal conductor, connected to PCB opposite connector.

PARAMETER: Parameter Min Typical Max Unit Figure Product size mm 61.5*33.5*13.5 Installation size mm 58.5*28.5 Display size mm 36*19.5 Weight 20 21 22 g Working voltage 10 100 V Common Working consumption 5 6 mA LED ON Voltage accuracy вђ.1 вђ.5 % Temperature accuracy вђ.5 в‘ вЊ Selective assembly Sleep consumption 6 10 12 uA 20V Working temperature -10 25 55 вЊ Buzzer volume 70 75 80 db Selective assembly Buzzer voltage 11.5 100 V adjustable INSTRUCTIONS:

The real-time detection of the battery temperature (Selective assembly).

The buzzer alarm switch, alarm voltage setting (Selective assembly).

The installation is simple, with a buckle, without screws.

The red indicator flashes to alarm when it is low battery.

The product can go to sleep after 10 seconds.

The 10~100V wide input voltage, reverse protection.

To display the percentage of remaining battery power, voltage, temperature.

To customize the type of battery, suitable for lead-acid, lithium-ion batteries, lithium iron phosphate, metal hydride battery, etc.

The color liquid crystal material, clear display, display softly at night.

#Drok battery monitor 48volt full#

The patented product adopted neutral packaging production, with the simple dustproof waterproof surface, with a full protection cover.

The default parameters are suitable for lithium batteries, lead-acid batteries, lithium iron phosphate battery, Ni MH battery application field through the development of programming, can be applied to any battery, simple wiring, convenient maintenance, and disassembly using a standard connector. This product is a general instrument, adopts LCD color screen, can long-term display the battery, voltage, temperature (Selective assembly sound-light alarm (Selective assembly) can be used in a variety of lighting conditions.